OO Gauge NER Water Crane Kit (hat) With Overflow tank based on Goathland Station

See our other listing via the shop for the version without the cone

FAQ – Product FAQs

General Product FAQs

What exactly do I get with this NER Water Crane set?

You receive three grey resin printed pieces: one NER-style water crane with the “Top Hat” cone on the tower, one overflow tank, and one control stand. These are supplied unassembled (if needed), unprimed and unpainted, with all supports removed.

Is this model based on a real location?

Yes, this is our interpretation of the NER water crane at Goathland Station, complete with the distinctive “Top Hat” cone on top of the tower. The painted example shown in the photos is based on the actual crane in situ at Goathland, run by the NYMR.

Does this model come painted like the photos?

No, the photos show painted examples for reference only. Your items arrive in grey resin, ready for you to prime and paint in your own style.

Is this suitable for layouts with steam locomotives?

Absolutely. A water crane and overflow tank are a classic feature for steam-era layouts, as steam locos are always being topped up with water in real life. This set makes an ideal lineside detail for any steam depot or station scene.

Is there a version without the “Top Hat” cone?

Yes, we also offer a version without the cone. You can find it in our shop as a separate listing.

How are the parts finished before shipping?

All items are cleaned and cured by hand, with supports removed. We do our best to remove support marks, but some light sanding may still be required before painting.

Troubleshooting FAQs

My model arrived broken in the post, what should I do?

If your item has been damaged during shipping, please take clear photos of the breakages and contact us. While we cannot be responsible for damage after safe delivery, we will always see what we can do to help if it has been broken in transit.

Some surfaces look slightly rough or show faint support marks. Is this normal?

With resin printing, very fine marks or slight texture can sometimes remain even after supports are removed. This is normal and usually only needs a little gentle sanding before priming to achieve a smooth finish.

One of the parts feels a bit flexible or delicate. Is that a problem?

Resin can be quite delicate, especially on finer details, so handle the parts carefully and avoid dropping them. A slight flex in thinner sections is not unusual, but they should be treated with care during assembly and painting.

The parts do not seem to sit quite flat on my layout.

Check that the base of each piece and the surface of your layout are both smooth and level. A tiny amount of sanding on the underside of the base or a thin layer of adhesive or filler under the model can help it sit flat and blend into the scenery.

There are small bits of cured resin or dust on the model. How should I clean it?

Use a soft brush (such as an old, clean paintbrush) to gently remove dust or loose particles. Avoid harsh solvents or soaking, as the parts are already fully cured. Once dust-free and lightly sanded where needed, you can go straight to priming.

Assembly & Painting FAQs

Do I need to assemble anything, or is it all one piece?

The set comes as three separate resin pieces: the water crane, overflow tank, and control stand. They are supplied unassembled (if needed), so you can position them on your layout as you wish. There is no complex multi-part kit assembly required.

How should I prepare the parts before painting?

First, inspect the parts for any fine support marks and gently sand them smooth. Then make sure the surfaces are free of dust. Once clean and smooth, you can apply your primer directly to the resin.

What paints and finishes were used on the example model?

The painted example shown uses Halfords red primer as a base, followed by an ink wash and some matt black acrylic. This combination gives a nicely weathered, work-worn appearance similar to the real crane at Goathland.

Do I need a special primer for the resin?

A good quality primer that adheres well to plastic is recommended. The example uses Halfords red primer, which gives a solid base coat and a suitable colour for further weathering and detailing.

Any tips for achieving a realistic, used look?

After priming, apply an ink wash to pick out the details and create depth in recesses. Then use matt black acrylic sparingly for areas of grime and soot. You can build up layers gradually, focusing on joints, bolts, and areas where water and dirt would naturally collect on the real crane and tank.